GATE EC 2023

65 questions · 100 marks · 180 minutes

Take this paper as a timed test
From RENYXERAPractise this subject in the exam simulatorTimed, GATE-style tests with analytics that find your weak topics.

GENERAL APTITUDE (GA)

  1. Q1"I cannot support this proposal. My will not permit it."Verbal Aptitude · Basic vocabulary · MCQ · 1 mark
  2. Q2Courts : : : Parliament : Legislature (By word meaning)Verbal Aptitude · Basic vocabulary · MCQ · 1 mark
  3. Q3What is the smallest number with distinct digits whose digits add up to 45?Quantitative Aptitude · Numerical computation and estimation · MCQ · 1 mark
  4. Q4In a class of 100 students, (i) there are 30 students who neither like romantic movies nor comedy movies, (ii) the number of students who like romantic movies is twice the number…Quantitative Aptitude · Elementary statistics and probability · MCQ · 1 mark
  5. Q5How many rectangles are present in the given figure?Spatial Aptitude · Transformation of shapes · MCQ · 1 mark
  6. Q6Forestland is a planet inhabited by different kinds of creatures. Among other creatures, it is populated by animals all of whom are ferocious. There are also creatures that have c…Analytical Aptitude · Logic: deduction and induction · MCQ · 2 marks
  7. Q7Which one of the following options represents the given graph?Quantitative Aptitude · Numerical computation and estimation · MCQ · 2 marks
  8. Q8Which one of the following options can be inferred from the given passage alone? When I was a kid, I was partial to stories about other worlds and interplanetary travel. I used to…Verbal Aptitude · Reading and comprehension · MCQ · 2 marks
  9. Q9Out of 1000 individuals in a town, 100 unidentified individuals are covid positive. Due to lack of adequate covid-testing kits, the health authorities of the town devised a strate…Quantitative Aptitude · Elementary statistics and probability · MCQ · 2 marks
  10. Q10A 100 cm 32 cm rectangular sheet is folded 5 times. Each time the sheet is folded, the long edge aligns with its opposite side. Eventually, the folded sheet is a rectangle of dime…Spatial Aptitude · Paper folding, cutting, and patterns in 2 and 3 dimensions · MCQ · 2 marks

ENGINEERING MATHEMATICS

  1. Q11Let v 1 = bmatrix 1 \\ 2 \\ 0 bmatrix and v 2 = bmatrix 2 \\ 1 \\ 3 bmatrix be two vectors. The value of the coefficient in the expression v 1 = v 2 + e , which minimizes the leng…Linear Algebra · Vector space · MCQ · 1 mark
  2. Q12The rate of increase, of a scalar field f(x, y, z) = xyz, in the direction v = (2, 1, 2) at a point (0, 2, 1) isVector Analysis · gradient · MCQ · 1 mark
  3. Q13Let w 4 = 16j. Which of the following cannot be a value of w?Complex Analysis · Analytic functions · MCQ · 1 mark
  4. Q14The value of the contour integral, C ( z+2 z 2+2z+2 ) dz, where the contour C is \ z : z + 1 - 3 2 j = 1 \ , taken in the counter clockwise direction, isComplex Analysis · Cauchy's integral formula · MCQ · 1 mark
  5. Q15Let the sets of eigenvalues and eigenvectors of a matrix B be \ k 1 k n\ and \ v k 1 k n\ , respectively. For any invertible matrix P, the sets of eigenvalues and eigenvectors of…Linear Algebra · eigen values and eigen vectors · MCQ · 1 mark
  6. Q36A random variable X, distributed normally as N(0, 1), undergoes the transformation Y = h(X), given in the figure. The form of the probability density function of Y is (In the opti…Probability and Statistics · probability distributions · MCQ · 2 marks
  7. Q37The value of the line integral P Q (z 2\, dx + 3y 2\, dy + 2xz\, dz) along the straight line joining the points P\,(1, 1, 2) and Q\,(2, 3, 1) isCalculus · line, surface and volume integrals · MCQ · 2 marks
  8. Q38Let x be an n 1 real column vector with length l = x T x . The trace of the matrix P = x x T isLinear Algebra · matrix algebra · MCQ · 2 marks
  9. Q55The value of the integral R xy\, dx\, dy over the region R, given in the figure, is (rounded off to the nearest integer).Calculus · multiple integrals · NAT · 2 marks

CORE EC

  1. Q16In a semiconductor, if the Fermi energy level lies in the conduction band, then the semiconductor is known asSemiconductor Fundamentals · energy bands in intrinsic and extrinsic semiconductors · MCQ · 1 mark
  2. Q17For an intrinsic semiconductor at temperature T = 0 K, which of the following statement is true?Semiconductor Fundamentals · energy bands in intrinsic and extrinsic semiconductors · MCQ · 1 mark
  3. Q18A series RLC circuit has a quality factor Q of 1000 at a center frequency of 10 6 rad/s. The possible values of R, L and C areTime and frequency domain analysis of linear circuits · RL, RC and RLC circuits · MCQ · 1 mark
  4. Q19For a MOS capacitor, V fb and V t are the flat-band voltage and the threshold voltage, respectively. The variation of the depletion width (W dep ) for varying gate voltage (V g) i…Semiconductor Devices · MOS capacitor · MCQ · 1 mark
  5. Q20Consider a narrow band signal, propagating in a lossless dielectric medium ( r = 4, r = 1), with phase velocity v p and group velocity v g. Which of the following statement is tru…Plane Waves and Properties · phase and group velocity · MCQ · 1 mark
  6. Q21In the circuit shown below, V 1 and V 2 are bias voltages. Based on input and output impedances, the circuit behaves as aBJT and MOSFET Amplifiers · small signal analysis · MCQ · 1 mark
  7. Q22A cascade of common-source amplifiers in a unity gain feedback configuration oscillates whenOp-amp Circuits · phase margin · MCQ · 1 mark
  8. Q23In the circuit shown below, P and Q are the inputs. The logical function realized by the circuit shown below isCombinatorial circuits · logic gates and their static CMOS implementations · MCQ · 1 mark
  9. Q24The synchronous sequential circuit shown below works at a clock frequency of 1 GHz. The throughput, in Mbits/s, and the latency, in ns, respectively, areSequential Circuits · critical path delay · MCQ · 1 mark
  10. Q25The open loop transfer function of a unity negative feedback system is G(s) = k s(1+sT 1)(1+sT 2) , where k, T 1 and T 2 are positive constants. The phase cross-over frequency, in…Control Systems · Routh-Hurwitz and Nyquist stability criteria · MCQ · 1 mark
  11. Q26Consider a system with input x(t) and output y(t) = x(e t). The system isLTI systems · definition and properties · MCQ · 1 mark
  12. Q27Let m(t) be a strictly band-limited signal with bandwidth B and energy E. Assuming 0 = 10B, the energy in the signal m(t) 0 t isContinuous-time Signals · Fourier series and Fourier transform · MCQ · 1 mark
  13. Q28The Fourier transform X( ) of x(t) = e -t 2 is Note: - e -y 2 \, dy =Continuous-time Signals · Fourier series and Fourier transform · MCQ · 1 mark
  14. Q29In the table shown below, match the signal type with its spectral characteristics.Continuous-time Signals · Fourier series and Fourier transform · MCQ · 1 mark
  15. Q30For a real signal, which of the following is/are valid power spectral density/densities?Random Processes · Autocorrelation and power spectral density · MSQ · 1 mark
  16. Q31The signal-to-noise ratio (SNR) of an ADC with a full-scale sinusoidal input is given to be 61.96 dB. The resolution of the ADC is bits (rounded off to the nearest integer).Data Converters · ADCs and DACs · NAT · 1 mark
  17. Q32In the circuit shown below, the current i flowing through 200\, resistor is mA (rounded off to two decimal places).Circuit Analysis · Node and mesh analysis · NAT · 1 mark
  18. Q33For the two port network shown below, the [Y]-parameters is given as [Y] = 1 100 bmatrix 2 & -1 \\ -1 & 4/3 bmatrix S The value of load impedance Z L, in , for maximum power trans…Time and frequency domain analysis of linear circuits · Linear 2-port network parameters · NAT · 1 mark
  19. Q34For the circuit shown below, the propagation delay of each NAND gate is 1 ns. The critical path delay, in ns, is (rounded off to the nearest integer).Sequential Circuits · critical path delay · NAT · 1 mark
  20. Q35In the circuit shown below, switch S was closed for a long time. If the switch is opened at t = 0, the maximum magnitude of the voltage V R, in volts, is (rounded off to the neare…Time and frequency domain analysis of linear circuits · RL, RC and RLC circuits · NAT · 1 mark
  21. Q39The V OUT V IN of the circuit shown below isOp-amp Circuits · Amplifiers · MCQ · 2 marks
  22. Q40In the circuit shown below, D 1 and D 2 are silicon diodes with cut-in voltage of 0.7 V. V IN and V OUT are input and output voltages in volts. The transfer characteristic isDiode Circuits · Clipping · MCQ · 2 marks
  23. Q41A closed loop system is shown in the figure where k > 0 and > 0. The steady state error due to a ramp input (R(s) = /s 2) is given byControl Systems · Transient and steady-state analysis of LTI systems · MCQ · 2 marks
  24. Q42In the following block diagram, R(s) and D(s) are two inputs. The output Y(s) is expressed as Y(s) = G 1(s)R(s) + G 2(s)D(s). G 1(s) and G 2(s) are given byControl Systems · Block diagram representation · MCQ · 2 marks
  25. Q43The state equation of a second order system is x (t) = A x (t), x (0) is the initial condition. Suppose 1 and 2 are two distinct eigenvalues of A and v 1 and v 2 are the correspon…Control Systems · State variable model and solution of state equation of LTI systems · MCQ · 2 marks
  26. Q44The switch S 1 was closed and S 2 was open for a long time. At t = 0, switch S 1 is opened and S 2 is closed, simultaneously. The value of i c(0 +), in amperes, isTime and frequency domain analysis of linear circuits · RL, RC and RLC circuits · MCQ · 2 marks
  27. Q45Let a frequency modulated (FM) signal x(t) = A ( c t + k f - t m( )\, d ), where m(t) is a message signal of bandwidth W. It is passed through a non-linear system with output y(t)…Analog Communications · angle modulation and demodulation · MCQ · 2 marks
  28. Q46The h-parameters of a two port network are shown below. The condition for the maximum small signal voltage gain V out V s isTime and frequency domain analysis of linear circuits · Linear 2-port network parameters · MCQ · 2 marks
  29. Q47Consider a discrete-time periodic signal with period N = 5. Let the discrete-time Fourier series (DTFS) representation be x[n] = k=0 4 a k e jk2 n 5 , where a 0 = 1, a 1 = 3j, a 2…Discrete-time Signals · DFT · MCQ · 2 marks
  30. Q48Let an input x[n] having discrete time Fourier transform X(e j ) = 1 - e -j + 2e -3j be passed through an LTI system. The frequency response of the LTI system is H(e j ) = 1 - 1 2…Discrete-time Signals · DTFT · MCQ · 2 marks
  31. Q49Let x(t) = 10 (10.5Wt) be passed through an LTI system having impulse response h(t) = ( Wt t ) 2 10Wt. The output of the system isLTI systems · frequency response · MCQ · 2 marks
  32. Q50Let x 1(t) and x 2(t) be two band-limited signals having bandwidth B = 4 10 3 rad/s each. In the figure below, the Nyquist sampling frequency, in rad/s, required to sample y(t), isContinuous-time Signals · Nyquist sampling theorem · MCQ · 2 marks
  33. Q51The S-parameters of a two port network is given as [S] = bmatrix S 11 & S 12 \\ S 21 & S 22 bmatrix with reference to Z 0. Two lossless transmission line sections of electrical le…Transmission Lines · S-parameters · MCQ · 2 marks
  34. Q52The standing wave ratio on a 50\, lossless transmission line terminated in an unknown load impedance is found to be 2.0. The distance between successive voltage minima is 30 cm an…Transmission Lines · Equations · MSQ · 2 marks
  35. Q53The electric field of a plane electromagnetic wave is E = a x C 1x ( t - z) + a y C 1y ( t - z + ) V/m . Which of the following combination(s) will give rise to a left handed elli…Plane Waves and Properties · polarization · MSQ · 2 marks
  36. Q54The following circuit(s) representing a lumped element equivalent of an infinitesimal section of a transmission line is/areTransmission Lines · Equations · MSQ · 2 marks
  37. Q56In an extrinsic semiconductor, the hole concentration is given to be 1.5n i where n i is the intrinsic carrier concentration of 1 10 10 \ cm -3 . The ratio of electron to hole mob…Carrier Transport · drift current · NAT · 2 marks
  38. Q57The asymptotic magnitude Bode plot of a minimum phase system is shown in the figure. The transfer function of the system is G(s) = k(s+z) a s b(s+p) c , where k, z, p, a, b and c…Control Systems · Bode and root-locus plots · NAT · 2 marks
  39. Q58Let x 1(t) = u(t + 1.5) - u(t - 1.5) and x 2(t) is shown in the figure below. For y(t) = x 1(t) x 2(t), the - y(t)\, dt is (rounded off to the nearest integer).LTI systems · convolution · NAT · 2 marks
  40. Q59Let X(t) be a white Gaussian noise with power spectral density 1 2 W/Hz. If X(t) is input to an LTI system with impulse response e -t u(t). The average power of the system output…Random Processes · filtering of random signals through LTI systems · NAT · 2 marks
  41. Q60A transparent dielectric coating is applied to glass ( r = 4, r = 1) to eliminate the reflection of red light ( 0 = 0.75\ m ). The minimum thickness of the dielectric coating, in…Plane Waves and Properties · Reflection and refraction · NAT · 2 marks
  42. Q61In a semiconductor device, the Fermi-energy level is 0.35 eV above the valence band energy. The effective density of states in the valence band at T = 300 K is 1 10 19 \ cm -3 . T…Semiconductor Fundamentals · equilibrium carrier concentration · NAT · 2 marks
  43. Q62A sample and hold circuit is implemented using a resistive switch and a capacitor with a time constant of 1\, . The time for the sampling switch to stay closed to charge a capacit…Data Converters · Sample and hold circuits · NAT · 2 marks
  44. Q63In a given sequential circuit, initial states are Q 1 = 1 and Q 2 = 0. For a clock frequency of 1 MHz, the frequency of signal Q 2 in kHz, is (rounded off to the nearest integer).Sequential Circuits · counters · NAT · 2 marks
  45. Q64In the circuit below, the voltage V L is V (rounded off to two decimal places).Circuit Analysis · Node and mesh analysis · NAT · 2 marks
  46. Q65The frequency of occurrence of 8 symbols (a-h) is shown in the table below. A symbol is chosen and it is determined by asking a series of "yes/no" questions which are assumed to b…Information Theory · source coding · NAT · 2 marks